Lab Mills IRM Model: 2050 Hot Lab Rolling Mill with Inline Push through Preheating Oven Mill Speed: 0-30 RPM (approximately) Mill Power: 7.5 HP, 220 V, 3-phase The rolls rotate on precision bronze bearings and are simultaneously driven by a pinion stand. The roll height is adjustable independently or simultaneously through a side-wheel screw down assembly. There are entry and exit tables with adjustable guides installed on the entry table. The AC tech inverter is designed for variable speed with forward, reverse, and dynamic breaking. Emergency stop bars will be installed on entry and exit of mill. In addition, all controls are in a centrally located operating station. Each roll temperature is independently administered by a Watlow controller, which can be controlled up to 600 degrees Fahrenheit . Mill Dimensions: 48" L x 24" W x 48" H (approximately) Weight: 2,000 lbs (approximately) Oven Specs: Chamber size: 12" L x 6" W x 2-1/4" H Max Temp: 2250 degrees Fahrenheit Power: 220 volt single phase Oven Elements: silicon carbide Heat Controls: The Watlow heat controller is located in a central control panel and the muffle has a fitting to introduce atmosphere. In addition, the heat chamber's exit pass line will be in line with the mill entrance table. Furthermore, the oven is mounted on wheels with locking mechanisms so that it can be used with the mill or independently. Lastly, a push rod is supplied to help push the material in and out of the oven. Oven Dimensions: 48" L x 24" W x 60" H (approximately) Weight: 1,000 lbs (approximately) IRM MODEL # 4060 LAB ROLLING MILL ON A BASE Both rolls are driven by a heavy-duty pinion stand. The roll position is adjustable either independently or simultaneously. Powered by a 5 HP DC motor, the separating force of the mill is approximately 40,000LBS. This motor has a variable speed programmable AC tech drive allowing the mill to have a forward and reverse. In addition, the mill is equipped with Lexan guards, emergency stop bus on entry and exit tables. Mill power requirements: 220V, 15 amps, and 3 phase. Roll size: Diameter: 4.000" Width: 6.000" Roll material: 52100 tool steel 60-62 Rockwell C Pass-line Height: 40 1/2" Mill weight: 1500 Lbs. (Approximately) Dimensions of total unit: (Approximately) 51" L x 21" W x 58" H Available mill options: Wire rolls Heated rolls IRM Lab Mill Table Model This large lab mill is powered with a 110 volt, 1 H.P. DC variable speed motor connected to a reducer to achieve 0 to 30 RPM. The separating force of the mill is approximately 20,000 LBS. . Lab Rolling Mill Bench Model The mill and drive are mounted on a 1" thick aluminum plate complete with all electrics and controls. Rolls: up to 6" wide. Mill weight: 150 Lbs. (Approximately) IRM Lab Mill On Base This large lab mill on a base is powered with a 110 volt, 1 HP DC variable speed motor connected to a reducer to achieve 0 to 30 RPM. The separating force of the mill is approximately 20,000 LBS. The mill and drive are mounted on a steel base complete with all electrics and controls. This mill can be equipped with entry and exit tables. Rolls: up to 6" wide. Weight: 500 lbs. (Approximately). IRM Lab Mill Bench Model With Optional Heated Rolls Rolls: Diameter - 3.750"-6". 0-17 RPM. The separating force of the mill is approximately 25,000 LBS. The mill and drive are mounted on a 1" thick aluminum plate complete with all electrics and controls. The mill can be equipped with entry and exit tables. In addition, it can also be equipped with heated rolls delivering 0-600 degrees F. Rolls are adjustable independently or simultaneously; adjustment knobs are equipped with indicators. Width: from 6" to 12" IRM Carbide Wire Flattening Mill This machine is equipped with high precision SKF German roller bearings and mounted on an aluminum plate 1" thick x 10" wide x 24" long. Furthermore, it is equipped with 110 volt, 1 HP DC forward and reversing and connected to a reducer to achieve 0 to 30 RPM. The speed can be adjusted to customer spec. Roll width: 2.312. Roll Diameter: 2.750. Carbide Width: 1.125. Roll Material: Tungsten Carbide Ring polished to a mirror finish IRM Model 20050 The rolls are chrome plated and rotate on precision bronze bearings with cleaning pad assembly. In addition, they also have air pay off with 3" diameter mandrels and a re-coiler with an air clutch and a 3" mandrel. Each mill of this model is supplied with emergency stop bars on the entry and exit of mill. The roll adjustments are side wheel adjustable. The separating force is approximately 75,000 lbs LBS. Also, the rolls can be water-cooled or heated. Motor: 7.5 HP motor 220 volt three phase. Variable speed: from 0-30 feet per minute. Mill Dimensions: 48.L x 48.W x 60.H Approximate weight: 2500lbs. CONTACT US with your requirements. Your satisfaction is guaranteed!